String bracelet designs - How to make string bracelets best friendship bracelet pattern

Prepare the Materials:

No.72a red cord 1meters
No.72a green cord 1meters
No.72a peach cord 1meters
No.72a sky blue cord  1meters
No.72a gold yellow cord 1meters
No.72 yellowish cord  1meters
925 Sterling Silver Leaf-shaped Charm Pendants 2
925 Sterling Silver Hollow Bead 1
Others:Scissor, Measuring tapes ,lighter
 
 
Steps:

Step 1:
Cut two pieces of red cords at least 50cm long. Fold the yellowish cord in half. Then take one of red cord under the yellowish cord
 

Step 2:
Tie a small knot with the red cord.


Step 3:
Fold the left cord and take hold of cord with your bracelet. Then take the right red working cord end and bring it up and over the holding yellowish cords again and again towards yellowish cord end position.
 

Step 4:
When you reach the length that about 2cm on your bracelet, tie a small knot with a 50cm sky blue cord in case the red cord loosed off.
 

Step 5:
Continue wrapping the sky blue cord.
 

Step 6:
Add the different color cord and continue wrapping the working end.
 

Step 7:
Once you braided half of the bracelet, add on the 925 sterling silver leaves.
 

Step 8:
Repeat the same steps 6 till it reach your desired length.
 

Step 9:
Tie an overhand knot after string a 925 sterling silver Hollow Bead.
 

Step 10:
Trim the excess cords.

Handcrafted jewelry project friendship bracelets patterns homemade sterling silver clover charm bracelets colorful string bracelet

 

Prepare the Materials:

No.72a peach cord 1.6meters

No.72a sky blue cord 1.6meters

No.72a gold yellow cord 1.6meters

925 Sterling Silver Thai Silver Mosaic Four-leaf clovers Bead 1

Others:Scissor, Measuring tapes ,lighter

 

Steps:

Step 1:

Cut two pieces of cords that are at least 32 inches (0.8meters) long. Now you have six cords and each cords are 32 inches (0.8meters) long.

 

Step 2:

Fold one of the peach cord in half and take it through the hole of Silver Mosaic Four-leaf clovers Bead.

 

Step 3:

Pull the other two cords through the hole of bead. Then pull the three cords through the loop. (As shown in the picture)

 

Step 4:

Take the left peach cord over the holding cords and put it under the right peach cord.

 

Step 5:

Put the peach cord on the right over the other peach cord from the left and under the holding cords in between. And then take it out from left loop on the left. The braiding method above is called square knot.

 

Step 6:

Repeat the same steps 4 and 5. Continue braiding the rest of cord and you’ll create the spiral pattern.

 

Step 7:

Stop braiding when reached 3cm. Now change another cord, pull the blue sky cord and continue braiding bracelet by using the above method.

 

Step 8:

Again, pull the gold yellow cord and continue braiding bracelet by using the above method.

 

Step 9:

Repeat the same process on the other side. Compare the left to right, keep them as equal length.

 

Step 10:

Trim the excess cords and tie a small knot to secure your bracelet.

 

Cool sterling silver charm for string bracelet making ideas - How to make cool bracelets

 

Prepare the Materials:

NO.72 Brown cord 160inches (4 meters)

925 Sterling Silver Thai Silver Cross Vajra Charm 1

Others:Scissor, Measuring tapes

 

Steps:

Step 1:

This step was explained earlier. For details about how to start your bracelet, refer to the Handcraft 925 Sterling Silver Tube Bending Unisex Braided Bracelets DIY04.

 

Step 2:

String a Thai Silver Cross Vajra Charm.

 

Step 3:

Continue braiding the bracelet by using the corn knot. Compare the left to the right, keep them as equal length.

 

Step 4:

When reach your desired length, tie a small knot.

 

Step 5:

Done it!

 

Good friendship bracelet designs (black eyes) - how to make braided bracelets

Prepare the Materials:

6mm Natural Green Jadeite Black Agate Bead 1
8mm Natural Green Jadeite Black Agate Beads 8
NO.72 bright red cord  200 inches  (5 meters)
Others:Scissor, Measuring tapes ,lighter



Steps:

Step 1:
Cut two pieces of cords that are at least 40 inches (1 meter) long. Now there two cords are 40 inches (1 meter) long each, and the other one is 120 inches (3 meters) long. Then, get the 2 short cords together with an overhand knot in the middle place.
 

Step 2:
Pull the 120 inches (3meters) cord and start braid bracelet by using the square knot. Then string an 8mm black agate bead with the middle of two cords.
 

Step 3:
Starting with the outer-right cord, tie a backward knot (as shown) make a ninety degree angle with the tying cord over the top of the cord you are tying it to.


Step 4:
Now pick up the outermost cord on the left side and make a forward knot by creating a 4-shape over the 2nd cord.
 

Step 5:
Repeat the same steps 3 and 4. Continue braiding still reach the length that at the bottom of black agate bead.
 

Step 6:
Pull the longest cords, and continue braiding bracelet by using the square knot.
 

Step 7:
Repeat the same process for the next cords.
 

Step 8:
Every now and then please note to check the length against your wrist. Stop braiding when reach your desired length.
 

Step 9:
String a 6mm black agate bead with the middle of cords.
 

Step 10:
Trim the excess cord and burn the tails of cords.
 

Step 11:
Your creation is finished.
 

Friendship bracelets patterns Cool friendship bracelets instructions friendship bracelet designs

Prepare the Materials:

Sterling silver bead

Sterling silver tub bending

red cords/black cords/brown cords

Others:Scissor, Measuring tapes

 

Steps:

Step 1:

Prepare two cords, if circumference of your wrist is approx 16cm, the cords should be 2 meters.

 

Step 2:

Step 2: Bring the two cords together and fold them in half. Then start braiding snake knots from the center-left. 2.2mm snake knots is enough here to see snake knot tutorial.

 

Step 3:

Tie the four cords together with a secure knot.

 

Step 4:

Thread one more 1m cord to the middle of four cords and start to braiding corn knots.Click here to see corn knot tutorial.

 

Step 5:

Stop braiding when it reach your desired length.

 

Step 6:

Thread the hollow out sterling silver bend on.

 

Step 7:

Tie an overhand knot at the end. Trim the 4 of cords and burn threads. Threading sterling silver beads to the rest of cords, and then tie an over hand knot.

 

Step 8:

Trim the needless cords, Burn the excess threads.

 

Step 9:

Done it!